EEMANN TECH

Reference: ET-130029

Made from Brass that increases the weight of the pistol and improves the balance when shooting. The grips are attached with the factory screws and a spare set is provided.
To avoid the grip panels becoming loose we recommend the use of Blue Loctite or mild strength thread locker.
Self-adhesive grip tape is provided for attachment to each grip panel with a spare set provided.
There is also rectangular-shaped grip tape for use on the front and backstop of your pistol if allowed by your division rules.
The SHORT grips are designed to work with and accommodate a Magwell!

Not compatible with CZ compact models!

Material: Brass

Set contains:
• 1 x Brass Short Grip Left
• 1 x Brass Short Grip Right
• 2 x Grip Tape Set (44-130022)
• 2 x CZ OEM Grip Screw

Available sizes:
• Small - thickness: 0,8 mm (Thinnest in the world)
• Medium - thickness: 1,8 mm
• Large - thickness: 2,8 mm
• Extra Large - thickness: 3,8 mm

Weight: 
• Small- 66 gr (1 pc) / 132 gr (2 pcs)
• Medium- 88 gr (1 pc) / 176 gr (2 pcs)
• Large- 109 gr (1 pc) / 218 gr (2 pcs)
• Extra Large- 120 gr (1 pc) / 240 gr (2 pcs)

https://b2b.eemann.tech/et-cz-75/1510-2990-eemann-tech-brass-short-grips-for-cz-75-cz-75-ts-cz-shadow-2.html#/87-size-xl

Reference: ET-130067

Eemann Tech sear spring installation tool for CZ 75 pistols and their clones.

The Eemann Tech sear spring tool will revolutionize your sear spring installation.

Either for general maintenance or because your spring broke, on the range, or in your workshop, this tool will simplify a normally very tricky job and substantially reduce the time it usually takes.

You can replace or install your sear spring in seconds without any experience. We recommend the installation of the Eemann Tech Competition sear spring part number 131113 or the Eemann Tech extended competition sear spring part number 131114.

The new Eemann Tech sear spring tool incorporates a tiny neodymium magnet which holds the sear spring very securely whilst the short leg of the sear spring rests in a micro hole within the tool.
There are special relief cuts in the tool that allow it to be positioned correctly for the installation.

The tool is made of brass that is softer than the spring and thus will not damage it, but it's hard enough to perform the task.

Compatible with all cz 75 type pistols and their clones:
• CZ 75 pistols
• CZ Shadow 2 pistols
• Tanfoglio pistols

Material: Brass

How to use the tool, check our special video on YouTube channel.
https://www.youtube.com/eemanntech

https://b2b.eemann.tech/et-tools/6009-eemann-tech-sear-spring-installation-tool-for-cz.html

Reference: ET-130127

We are excited to present the Eemann Tech Thumb Rest Slide Stop for the CZ Shadow 2 / TS / TS2 pistols and their models.

This is a completely new design integrated with new ergonomics!

It is compatible with small, medium, and large size hands. Just put your finger on the thumb rest and feel the difference!

The Eemann Tech Thumb Rest Slide Stop for CZ Shadow 2/TS/TS2 is made from one piece of carbon steel and CNC machined to the highest standards.

It is designed to be used with CZ Shadow 2 / CZ TS / CZ TS2  firearms and their models.

Advantages:
• No firearm modification required
• Provides stability and consistent grip for recoil control
• Slide stop thumb rest functions as a normal slide stop allowing the slide to lock back if required
• Legal in IPSC Standard and Open divisions, and fits in IPSC Standard Box
• Special serration helps to keep your thumb in place
• Extended rod from the right side allows you to remove the slide stop from the firearm easily

Installation:
Remove the existing slide stop and replace it with the Eemann Tech Thumb Rest Slide Stop for CZ Shadow 2 / TS / TS2

Color:
• Black

Compatibility:
• CZ Shadow 2
• CZ Shadow 2 Orange
• CZ Shadow 2 Compact
• CZ 75 Tactical Sport
• CZ TS2
• CZ TS2 Race Green
• CZ TS2 Bronze

Material:
• Steel

Total width: ~44mm ( ~1,73" )
Thumb rest width: ~33mm ( ~1,29" )

https://b2b.eemann.tech/et-cz-shadow-2/8026-eemann-tech-130127-thumb-rest-slide-stop-for-cz-shadow-2-ts-ts2-black.html

Reference: ET-130086

The shape of the ultimate trigger was developed with the help of biomechanical engineers and physicians for the best possible ergonomics, performance, and perfect functioning of your trigger with the CZ platform.
The radius of the curve in the trigger is halfway between the factory trigger and our flat trigger giving the best of both.

There are two adjustable screws the trigger that allow for custom adjustment in both directions, both pre- and after-travel.
The ability to remove unnecessary pre-travel allows the trigger in double action mode to have a shorter reach which helps with smaller hands.
The over-travel screw allows for a shorter press and reset.

The end of the trigger has a tighter radius than the factory model and won't bottom out against the frame of the pistol, it also allows for smaller hands to feel more comfortable.

The DA/SA Ultimate Trigger allows for more precise control of the trigger press and reset!

Specially produced for use in Double Action mode with your CZ pistol

Works perfectly with all steel-framed CZ pistols with any installed disconnectors.

NOTE: Due to the difference in tolerances and thickness of pistol coating you may not need the Double Action Pre Travel Screw 4mm and 3mm in the CZ Shadow 2 Platform, they may not function because of little available pre-travel.

Compatible with:
• CZ 75
• CZ 75 SP-01
• CZ 75 SP-01 Shadow
• CZ 75 SP-01 Phantom
• CZ 75 SP-01 Shadow Line
• CZ 75 SP-01 Shadow Orange
• CZ 75 SP-01 Tactical
• CZ 75 B&BD
• CZ Shadow 2
• CZ Shadow 2 Orange

The set includes:
• Ultimate Trigger for CZ Shadow
• Screw for Eemann Tech triggers (after travel) for CZ (ET-131002)
• Screw for (pre-travel) adjustment - 4mm length (ET-131004)
• Screw for (pre-travel) adjust - 3mm length (ET-131003)
• Competition Trigger Pin (ET-130064)
• Competition Trigger Spring (ET-131109)
• 1.5 mm L-Shape Hex Key (ET-030012)

You have all you need for the perfect trigger group in one package

Installation takes only a few minutes.

Available colors:
• Black
• Silver
• Gold

Made from:
• Aluminium (Black, Silver)
• Brass (Gold)
• Steel (Black)

Legal in IPSC and USPSA Production

https://b2b.eemann.tech/et-cz-75/6079-19323-eemann-tech-ultimate-trigger-for-cz.html

Reference: ET-130052

The Eemann Tech Upgrade Kit is made for the most popular competition pistol in the world - CZ Shadow 2 and is used predominantly for IPSC, USPSA & any action sports.

All factory pistols are set to pass stringent tests with a multitude of ammunition hence the heavy springs and factory parts.

The most popular pistol, the CZ Shadow 2 is already made for competition-ready mode, but it’s always possible to improve the trigger group and other functions of your competition gun.

The upgrade kit ET-130052 has all the needed drop-in parts to upgrade your pistol from the box to full competition mode, without any major changes required to your platform.

The Eemann Tech Competition springs reduce the weight of the trigger and slide reciprocating recoil making it more sensitive and faster for competition use.

The Eemann Tech Extended Firing Pin eliminates misfire problems with your gun, if you are reloading and using hard primers or customized very light main spring.

The Eemann Tech Competition Disconnector will ensure an ultra-short reset without any additional modifications to your gun.

Eemann Tech Upgrade Kit ET-130052 for CZ Shadow 2 contains:
• ET-131140 Eemann Tech Recoil Spring for CZ 10 lbs. - 1pc.
• ET-131118 Eemann Tech Main Spring for CZ 8 lbs. - 1pc.
• ET-131109 Eemann Tech Competition Trigger Spring for CZ 75 - 1pc.
• ET-131156 Eemann Tech Competition Firing Pin Spring for CZ - 1pc.
• ET-131113 Eemann Tech Competition Sear Spring for CZ 75 - 1pc.
• ET-130044 Eemann Tech Competition Disconnector for CZ   - 1pc.
• ET-130015 Eemann Tech Extended Firing Pin for CZ - 1pc.
• ET-303017 Eemann Tech Competition Buffer for CZ 75 - 1pc.
• ET-130064 Eemann Tech Competition Trigger Pin for CZ - 1pc.
• ET-130055 Eemann Tech Hammer Strut Pin for CZ - 1pc.

Compatible with:
• CZ 75 SP-01 (without firing pin block models)
• CZ 75 Shadow Line
• CZ 75 SP-01 Shadow
• CZ 75 SP-01 Shadow Orange
• CZ Shadow 2
• CZ Shadow 2 Orange

https://b2b.eemann.tech/et-cz-shadow-2/4947-eemann-tech-upgrade-kit-for-cz-shadow-2.html