Current exhibitor list IWA OutdoorClassics 2022
More than 900 exhibitors from over 50 countries have already registered for IWA OutdoorClassics 2022. All registered exhibitors can be found in the current exhibitor list:
Exhibitor list (as of: 14.10.2021)
The exhibitor & product database of IWA OutdoorClassics 2021 shows all exhibitors who were registered for this exhibition. [status: 20.05.2021]
KNS PRECISION INC
KNS PRECISION INC
112 Marschall Creek Rd
We are a small weapons parts manufacturer located in Texas. We manufacture precision front sights for many weapon systems, non-rotate trigger/hammer pins, adapters for weapon mounts, and many other quality products.
AK Adjustable Piston System
Finally, a drop-in solution for taming the notoriously-overgassed AK platform. The patent-pending KNS AK Adjustable Gas Piston is a replacement for the AK’s piston head that attaches to the bolt carrier in about 10 minutes with no major gunsmithing or permanent modification required. The user is granted an extremely wide range of gas adjustment for suppressed and unsuppressed use, as well as a variety of different kinds of ammunition.
A good rule of thumb to determine if our piston will be useful, is if your gun throws the brass over 15 feet. This can signify excess gas pushing the carrier back at a higher velocity and pressure, than is needed for effective operation. This causes more recoil, more wear and tear, and less controllability. Many users are surprised to feel the difference in how their gun shoots with our Adjustable Gas Piston System installed.
There is no need to remove or replace your gas block for adjustability. Just change the piston, and go shoot.
Small Bore/Caliber pistons are for .223″, 5.56mm, and 5.45mm. They work better in AK’s of ALL CALIBERS with less excess gas.
Large Bore/Caliber pistons are for 7.62×39, .308″, and 7.62x54r.
Please email us with any questions on which piston will fit your firearm.
**When selecting your piston please refer to the chart pictured above to ensure maximized compatibility with your firearm.**
***A small percentage of Commercial Spec firearms have the piston welded to the carrier, instead of the usual Rivet holding in the Piston. We recommend purchasing a new carrier for the easiest installation.***
**** Vepr and Saiga Pistons will require drilling through the op-rod after screwing the piston into the carrier, due to variations in the staking location. These Op-Rods are Phosphated instead of Nitrided to allow easy drilling.****
-Tune almost any AK for suppressed use
-Decrease cyclic rate for full-auto fire
-US-made 922r Compliance Part
-Piston head assembly made from corrosion-resistant stainless steel
-All surface parts nitrided for durable, low-friction, & easily-cleaned operation
Non-Rotate Trigger/Hammer Pin Sets
These are the Generation 2 Mod 2 pin sets. These are the STRONGEST pins that can be produced and were designed to withstand the high impact of full and semi-auto 9mm, .223, and 7.62mm suppressed weapons. The pins are stainless steel. Black sideplates are black nitride treated, all other color options are DuraCoated. An absolute must-have for all M-16 owners. They will also protect your AR-15. Special anti-creep retainers prevent wear on your irreplaceable M-16 or AR-15 receiver. Pin installation tool & 2 Torx wrenches included. No modification to firearm required. THE TORQUE SPEC ON THE SCREW IS 11 inch/lbs. MAXIMUM. We recommend 8INCH/LBS of torque. IMPORTANT NOTE: The external width of some AR receivers may vary in the trigger/hammer pin area depending on the manufacturer. The pins being slightly too long will not affect the function or performance.
P415 Edge Rifle
The P415 was engineered over 10 years ago to be virtually unstoppable in unfavorable conditions.. It is a product of continuous development and improvement to the AR platform that no other rifle company has attempted. The reliability has been tested time after time, and the operating system perfected. E2 Extraction Technology, complete ambidextrous fire controls, modular free floating rail platform, and numerous internal improvements make it the pinnacle of all-purpose 5.56 caliber sporting rifles.
For 2017, we’ve cut the bulk. To minimize weight and maximize shooter comfort, the new P415 Edge features a redesigned handguard, reducing the size from the original by nearly 20%, making the width a mere 1.75 inches. Not only does this drop the weight down to 7 lbs, it provides even better ergonomics to the shooter. The P415 simply will not fail when you need it most.
POF USA Drop-In Straight 3.5lb Trigger
The flat-face single stage, non-adjustable drop-in trigger boasts a crisp 3.5 pound pull weight, red aluminum housing, and urethane feet for immediate competition, hunting, and tactical applications. Wire EDM cut from American A2 tool steel the trigger, disconnect and hammer are all nitride heat-treated for ultimate strength and corrosion resistance. All POF triggers come with KNS Precision stainless steel non-rotating anti walk pins specifically designed for POF USA’s ambidextrous lower receivers.
SwitchSight Folding Pistol Sights
Now you have a backup sight for your Red dot on your Glock. You don’t have to worry about a suppressor height sight blocking your view through the window of the red dot, or causing issues in your holster. Our SwitchSights are the best Glock sight available. They will stay neatly out of the way until your red dot fails and can be deployed quickly and easily.
Let’s talk Glocks and silencers. Specifically your sights. When you’re shooting your handgun with a silencer, you want higher profile sights to see over the silencer, right? And when the silencer comes off and the gun goes back in your holster you want lower profile sights. Current offerings force you to choose from a low or high profile only. Now you have the power to choose both!
Dead Air Silencers and KNS Precision have teamed up to develop the new SWITCHSIGHT. They work with your current holster and optics, and provide you the freedom to choose the correct orientation based on your Glock’s setup.
Made from Steel with a black nitride finish and featuring positive positioning, these sights will hold up to plenty of abuse and stay in the orientation you want them in.
Available for Glock only. Other pistols will be added soon.
*shown on a POF Glock slide
KNS PRECISION INC offers you products from these product groups:
Clicking on an exhibitor opens his profile with more information.