OD GREEN KP-15 COMPLETE W/ DMR TRIGGER & AMBI SELECTOR
WARNING!: This item is legally classified as a receiver. You Must be 21 years old to purchase this item and a resident of the same state your transferring dealer is licensed in.
The KP-15 is a monolithic polymer AR15 style receiver made from injection molded 30% glass filled nylon incorporating the buttstock, buffer tube, pistol grip, and trigger into the receiver design as integral components.
This manufacturing process offers several advantages
Lighter weight compared to similarly configured receivers
Lower cost to similarly configured receivers
Increased production speed and elimination of sub components through integration; especially important during high demand cycles in the market.
Compatibility with most common AR15 uppers and lower parts kits
Flared magwell to make reloads under stress easier to perform.
A1 Length 13” Length of Pull (LOP) Buttstock to fit a wide range of shooters
MLOK Slots at rear of stock for sling attachement points or run a strap through it for simple sling attachment
Holes at the front of the stock for QD socket inserts for more sling attachment options
Improved grip for comfortable use
“Winter” Trigger Guard
DMR Lowers Include:
KE Arms DMR Single Stage Trigger
KP-15 long hammer pin
KP-15 Optimized Ambi Selector
Carbine buffer and spring
Buffer Detent Assembly
Mil-Spec Magazine Catch Assembly
Mil-Spec Bolt Catch Assembly
Pivot and Take Down Pins
KP-15 Selector Detent
The KP-15 receiver uses a Carbine buffer and spring. Do NOT use anything other than standard carbine buffers and round springs or the JP SCSS in the KP-15.
The Take Down and Pivot Pins have the detents built into them; eliminating the spring and detent holes in the lower increases durability.
The buffer detent (should you choose to use it) is held in place with a 5/64” Roll Pin
The KP-15 is compatible with all Mil-Spec Fire Control Groups
The KP-15 is compatible with some cassette style match triggers including the KE Arms DMR and SLT units. The retention system of these triggers with D-Clips in the bushings to retain the fire control pins makes them better suited for use in the KP-15 than other designs that require captured pins.
The hammer pin area is wider for durability; Standard AR15 hammer pins can still be used but we offer a longer hammer pin for customers preferring a flush pin for aesthetic reasons.
Safety selector spring and detent load from the top and then the selector is slid over them. Standard selectors can work but removing them can be particularly difficult. We recommend the use of our optimized mil-spec selector or optimized ambi selector to make removal easier. Follow our assembly guide for further instructions.
The KP-15 is compatible with standard AR15 uppers in calibers including .223/5.56mm NATO, .300 Blackout, 7.62x39mm, 6.5mm Grendel, 6.8mm SPC, .350 Legend; make sure you use the appropriate weight carbine buffer for your rifle to eject casings at 3:00-4:00.
The KP-15 is compatible with 9mm blowback systems with a 5.4oz carbine buffer minimum. Use heavier buffers as long as your gun can cycle reliably. Failure to use this minimum buffer weight can damage the lower.
Big Bores: .450 Bushmaster, .458 SOCOM, .50 Beowulf, .50 BMG: We will never test these calibers enough to guarantee function and durability over time; use at your own risk.
Cerakoting: If you intend to have your KP-15 Cerakoted we recommend you use We Plead the 2nd as they are experienced in coating polymer receivers and have our authorization. The bake should be done at low temperatures (<190 Degrees F) and with an upper in place to prevent warping.
The KP-15 has a lifetime warranty for normal use.
Sling Attachment points wearing out is not grounds for a receiver replacement.
If the receiver breaks through misuse or neglect, we will replace it ONCE for $65.00.
Structural modifications including stock shortening and removal of material and dyeing the receiver void the warranty.
If you intend to register your KP-15 as an NFA weapon test it thoroughly before doing so in a Title 1 Configuration. Once you Form 1 or Form 2 it, you are legally the manufacturer and we cannot service or support it as easily. Should your receiver require warranty replacement we can only replace it with a title I receiver and we are not responsible for tax stamps or NFA fees.
Current Revised Instruction Sheet:
Leider gibt es für diesen Aussteller kein deutsches Firmenprofil.
KE Arms is a manufacturer specializing in products for the firearms industry. These product areas include complete firearms and components for AR15 and AR10 rifles, shotguns, pistols, and roller lock firearms. Our emphasis in manufacturing is robust quality and a dedication to the advancement of firearms technology and usability. Our team combines 25+ years of tier-one manufacturing experience in the automotive, aerospace and semi-conductor industries, along with modern combat in both Iraq and Afghanistan and law enforcement applications. Our competition shooting team actively participates in our cycle of research and development. This unique combination allows us to produce firearms and accessories with the most advanced tools and techniques in the industry that are specifically designed for real-world applications. Our products are all made in America by Americans